Renderoc plug

Repaid setting cement –based , water leak plugging mortar.

• Emergency water –stopping capability –sets in 8-10 seconds
• Single component –only the addition of clean water is required
• Excellent bond to the substrate
• Low exotherm – minimis thermal cracking
• pre-packed formulation to overcome variation in site batching.
• Contains no chloride admixtures.

For the rapid temporary patching and plugging of concrete segments , concrete and Brick tunnels linings , sewage system ,below ground access chambers, pipes, basements, foundations and mints

• 1.5 and 15 kg bags.

Renderoc plug should be added to clean water in the ratio of 3:1 respectively and placed immediately.

Nitobond EP

Epoxy resin –based concrete bounding agent used for bounding new with then old cementitious surfaces.

• More time : Enables to place the concrete up to 6 hours after applying Nitobond EP without the risk of delamination.
• High bond strength : Bond strength is more than the tensile strength of good quality concrete.
• Barrier coat: Acts as a barrier coat to the migration of chloride ions from host concrete.

Used for bounding new cementitious materials to existing cementitious surfaces. For use on vertical and be supported by formwork.

• 2.4-3.0 m2/liter depending on the surface

• 0.5, 1 and 4 liter packs

The entire contents of hardener should be poured into the resin container .two materials should mixed thoroughly until uniform color is obtained.

Conbextra GP2

Free –flow , high strength ,non-shrink, cementitious precision grout.

• Gaseous expansion system compensates for shrinkage and settlement in the plastic state .
• No metallic iron content to cause staining
• pre-packed material overcomes onsite batching variations.
• Develops high early strength without the use of chlorides
• High ultimate strength ensure the durability of the hardened grout
• Free flow ensures high level of contact with load bearing area.

Used for precision grouting where it is essential to withstand static and dynamic loads. It can also be used for anchoring a wide range of fixings.

• water to powder ratio: pourable =0.17: flow able =0.18.
• consistency: pourable 12.5: flow able 13.3 yield (liters)

• 25 kg bags.

The gauge water should be measured and added into the mixture .the content of ConbeXtra Gp2 Should be slowly added and should be mixed continuously for 5 mints.

Lokfix P

High strength polyester resin anchor grout for horizontal /overheads holes for anchoring /fixing Bolts , base plates , fan hooks, bars ,etc,

• Repaid strength gain
• Vibration/corrosion resistant
• Non –expansive and can be placed under water

• Staircase bolting
• structure repairs
• vertical connections
• grills
• Gates
• column/beam extensions

• 0.5 and 2.5 liter packs

A complete pack of resin and filer should be mixed mechanically to obtain a smooth and even consistency.

Lokfix S

Polyester resin based anchor grout for vertically down holes for anchoring /fixing bolts, Base plates, fan hooks , bars, etc.

• repaid strength gain
• vibration / corrosion resistant
• Non- expansive and can be placed under water

• staircase bolting
• structure repair
• vertical connections
• grills
• gates
• column/beam extensions

• 0.5 and 2.5 liter packs

A complete packs of resin and filter should be mixed mechanically to obtain a smooth and even consistency.

Brushbond

Acrylic polymer modified elastomeric waterproofing membrane coating for coating for concrete and masonry surfaces.

• Applied directly to the damp concrete and masonry
• Excellent adhesion and non-toxic
• Ideal for damp proofing basements
• Breathable

Provides a seamless waterproof coating suitable for use in water tanks, reservoirs, swimming pool and roofs.

• 16-18 m2 at 1 mm thickness (23 kg powder + 4 liter liquid)
• 4-4.5 m2 at 1 mm thickness (6 kg powder + 1 liter liquid)

• 23 kg powder + 4 liter liquid polymer pack
• 6 kg powder + 1 liter polymer pack

Nitobond BB is mixed equal volume of water with a slow speed drill; the powder component is added gradually to the liquid to avoid lump formation and mix for 2-4 mints.

Nitobond SBR Latex

Mortar and screed modifier cum bounding aid.

• Simple to use –single component , gauged as required
• High –provides excellent bond to concrete , adhesion plaster, masonry, stone work ,etc,
• Improves-Gives weather resistant mortar with improved durability impermeability to chlorides and Other harmful agents .
• Reduced –Provides water proof screeds, plasters and permeability slurries.
• Increase –compatible with all common hydraulic cements.
• Versatile- compatible with all common hydraulic cements.
• cost effective-Nitobond SBR(Latex) is economical to use

For modifying and improving bonding of floor toppings, renderings and mortars; repair of worn, damaged and spalled concrete, repair of large cracks; polymer modified floor screeds ; water proof plasters for masonary and slurries.

• Slurry primer-approximately 4-5 m2/liter depending on substrate porosity.

• 1.5, and 20 liter containers.